Monday, December 19, 2011

Hot Damn! Melted Plastic at last!

Over the weekend I finished re-assembling the Mendel and tried it out.  The Sanguionololu works great and so does the Sprinter firmware although I still expect to have a lot of tweaking for my specific machine.   Here's a quick pic of my first mess of plastic:

I think I will keep this blob on my desk as a post modernist sculpture

At first I could not get the filament to feed into the extruder.  I was trying to get it in by hand-turning the gear on the wade's extruder but it just didn't seem to be able to pick it up.  It was late and I was just going to give it up for the night when I realized that I was turning the gear the wrong way!  As soon as I turned it the other way the filament loaded into the hot end easily.  One more boneheaded move among many.

With the ATX power supply and the single board electronics my wiring is much cleaner.  I still seem to have a problem with my steppers though.  The X axis moves very slowly and the Y and Z axis don't move at all.  They just hum and jerk a bit.  I think that I may have them wired wrong but it was getting too late to get into troubleshooting last night so I will check it out tonight.

But, in general, it looks like I am finally ready to build some things.  Life is good.

Monday, December 5, 2011

Finally, Some Good News!

I wired up the Sanguinololu board last night and things went very well.  I jumpered the power enable pins on my new ATX power supply and then clipped the connector off of the 4 wire power connector and twisted the two power and two grounds wires together.  These were inserted in the screw terminals on the Sanquinololu board and then I plugged in the USB cable.  I got a steady green light so it looked like everything was ready to test.

I loaded up the Sprinter firmware that I had modified for my Mendel with no problems.  Then I confirmed that Pronterface can connect to the board.  I probably still have to do a lot of tweaking of the firmware but that can wait until I have a test print to use as a baseline.

My extruder is still disassembled from fixing the broken thermistor wire but I was able to wire it up on the bench to test it.  I had been holding off on reassembling it and mounting it back on the machine until I could confirm that it was working correctly since it is a major pain in the ass to remove.  I removed the 4 pin connector that came with my Botmill extruder and replaced it with two 2 pin connectors.  The heater and thermistor connectors on the Sanguinololu are on opposite ends of the board so their arrangement just wouldn't work.  After connecting with Pronterface the temp reported as 25C, which is about correct for my basement workshop so I went ahead and sent a command to heat up to 185C (PLA melting temp).  The heater worked and the thermistor immediately began reporting the correct temps as it rose  I confirmed that it heated up to the correct temperature and that it then started the regular on-off switching cycle in order to keep the temp stable.  Being fairly certain that I could melt plastic safely I then moved on to the steppers.

The Sanguinololu board expects 4 pin connectors and my old boards had screw terminals so I can't hook up the steppers until I get the correct connectors.   I had bought some locally only to find that I had the wrong ones.  I have a set coming in the mail but they have not arrived yet.  Luckily I have one stepper that arrived with the correct connector already attached so I used that one for testing.  I attached it to the extruder controller  and sent a command to extrude 5 mm.  The stepper kicked in and ran for what seemed to be the correct time period.  Hot Damn!

I then moved the motor to each of the X, Y, and Z controllers in sequence and tested them with the jog commands.  All seemed to be working correctly.  The only thing that I did not test was the opto-endstops.  I have to solder a joint between two pads on the board in order to set the voltage for them.  In my case this is 5v but I forgot to do it before I hooked everything up so it will have to wait until I take everything apart again prior to the final assembly..

So it looks like I am finally ready to print.  As soon as my connectors arrive I can do the final hookups of the steppers and move on the the really interesting part of this whole thing, the printing!

Tuesday, November 29, 2011

New Electronics

Sorry I've been gone for a while.  I finally threw up my hands and gave up on the Techzone electronics.  It seemed that, no matter what I did, I could not get any firmware to work correctly on it.  When I looked online I found that very few people were working with or supporting it so there wasn't the community that I needed to help me through it.  Given that sad situation I ordered a Sanguinololu and I have been waiting for it to arrive.

The new board arrived last night so I am back on track.  I will be using the Sprinter firmware since it seems to be fairly mature and has a good support community.  I hope to have time tonight to get things hooked up and tested.

Tuesday, November 8, 2011

More Progress, Same Problem

Last night I modified the heated bed and got it installed.  I attached the silicon heater element to the bottom (it's a simple peel and stick) so I just need to install a thermistor and wire it up to my control box and that will be ready to go.

Of course, a heated bed does me no good unless I can get this thing to extrude.  I switched out the thermistor again and got the same result.  Temp reads as 875 degrees at room temperature so the heater does not kick in.  I know that the thermistor is fine (I guess the previous one was OK as well) so I have another problem.  It wasn't until this morning on the way to work that I realized that I probably have the wrong temperature table in my firmware.  I will check that next.