Monday, November 7, 2011

Replacing the Thermistor

I finally got some free time to work on the Mendel yesterday.  I removed the extruder and replaced the thermistor with a spare one that I had laying around.  It involved carefully cutting away the Kapton tape and removing the thermistor leads from the crimped fitting that Botmill uses to connect it.  Not an extremely complicated procedure and it only took me about 20 minutes to replace it and re-crimp the connectors and tape the new thermistor in place.

I thought that I would do some testing prior to bolting the x-carriage back on the Mendel and it's a good thing that I did.  The temp showed as 875C so the heater never cut in.  When I checked the resistance of the thermistor I found it to be about 115K Ohms rather than the 80K that it should be.  Should have checked it before I installed it.  Either it is a bad thermistor or I picked up one with the wrong values at some point.  Luckily I have another one and it tests at the correct 80K so I will switch it out again.

Since I was dismantling things anyway I decided to switch out the build surface for the aluminum one that I bought to prepare for adding heating to it.  I removed the old one and then found that the aluminum plate blocked two of the holes in the plywood frame piece.  I will drill them out tonight.

I also made a cable with two female connectors so I could add a ground cable between the main and extruder boards.   I don't know if my problems with the extruder motor are due to grounding issues but this certainly can't hurt.

Thursday, October 20, 2011

A Quick Update

Just a short post here.  

I have discovered the source of at least one of my problems.  One of the leads on my thermistor is broken.  I think it may have burned through when I had the thermistor and the heater wired backwards.  In any rate, the thermistor reads as an open circuit and is definitely dead.  I will have to remove the extruder and dismantle the hot end to replace it.

I have also made up a ground wire to run between the main and extruder boards.  hopefully that will help to clean up the signals between the two boards and get the instructions to the extruder cleanly.

Tuesday, October 11, 2011

More progress - still no extrusion.

I didn't get as much time this weekend as I expected.  The furniture moving, along with the cooking and the Turkey Torpor, kept me out of the lab for most of it.

I did, however, get time to re-do the wiring for 12v power to the stepper controllers and the extruder board.  I had decided that poor wiring was causing some of my problems.  The issues with the steppers corelated with their distance from the power source. X and Y moved OK, Z was intermittent and the extruder didn't work at all.  This was due to my crappy job of wiring that caused more grounding problems as the power was passed down the line.  I rewired the whole thing and the problems disappeared.  I now have all 3 axis moving just fine with no squealing steppers and no pauses.

The extruder is still a problem though.  The motor doesn't do anything at all, which is odd since, last week, it was not moving but was squealing, indicating that it was getting some power when I sent a command.  Probably still a wiring issue.  Also, I noticed that the heater did not seem to shut off when I set the temperature to 0.  It seems to be getting power all the time so I guess I still have an issue with it.  I will get my IR thermometer from the garage so I can tell for sure what it is doing.

I will be logging in to the RepRap IRC chat tonight to see if someone can give me a fix for these items.  Progress is slow but at least it is progress.

Friday, October 7, 2011

Progress - in less than 10 minutes!

I only had about 10 minutes last night to work on the Mendel but I came away happy.  I had figured out that my firmware was probably not correct for my boards so I downloaded a new version specifically for the techzone hardware.  I loaded it up on both the main board and the extruder and got some great results.

All 3 axis are now working, although the Z axis seems to be intermittent. Sometimes it doesn't move when I jog it and the stepper makes a squealing sound as if it is jammed or something.  A couple of times it moved just fine though so I think that this is probably a hardware issue (something stuck in the gears etc.).  I will take a look at it tonight.  The correct commands are definitely getting to the steppers now though.  

Also, the hot end of the extruder is heating up just fine and the thermistor is passing good data back to the board.  I was using Pronterface last night and could easily track the temp as it went up.

I didn't have any filament in the machine but I hit "extrude 5 mm" a couple of times to see if the extruder stepper would rotate.  It didn't move so that is my biggest concern at the moment.  I set the desired temp to 0 and it still wouldn't move so I guess it is not something in the firmware as I had suspected.  I may have the stepper wired incorrectly but I didn't have time to check last night.

This will be a long weekend here in Canada for Thanksgiving and it is supposed to rain all weekend.  That means that I should have lots of time to work the bugs out and get something extruded.  I also have to move our entire home office down to the basement so my wife can have the spare room to set up an office for her new accounting business but what the heck, I have three whole days!